Maxim-integrated MAXQ7666 Manual do Utilizador Página 125
- Página / 386
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
MAXQ7665/MAXQ7666 User’s Guide
3-35
3.4.1 Temperature Sensor Signals
The MAXQ7665/MAXQ7666 temperature sensor uses four (one external diode can be connected between AIN0/AIN1, and a second
diode between AIN2/AIN3) external signals in remote temperature sensor drive configuration as explained in Table 3-10.
Table 3-10. Temperature Sensor Signals
The MAXQ7665/MAXQ7666 temperature sensor block works with the on-chip SAR ADC. Therefore, ensure the ADC is enabled (utility
ROM routine handles this) with the required external reference and supply. The temperature sensor has been calibrated for operation
with a +5V ADC reference level. It is possible to use other reference levels, but with diminished accuracy.
3.4.2 Using the Temperature Sensor
The following is an overview of the setup required for using the temperature sensor (internal or remote). The full details are available
as part of the utility ROM routine.
1) Temperature sensor and ADC must be enabled in the analog power enable register (APE).
2) Set up ADC configuration as follows in the ADC control register (ACNT).
ADCCS: conversion start from ADC start bit (111)
ADCDUL: single edge (0)
ADCBIP: unipolar conversion (0)
ADCDIF: single-ended or differential input (only for remote configuration)
3) Configure ADCMX4:ADCMX0 bits in the ACNT register as follows to enable/control temperature measurement.
ADCMX4: This bit must be set to configure ADC input channel for temperature measurement.
ADCMX3: Set this bit to configure temperature sensor drive current to high value. Clear this bit to configure temperature sensor
drive current to low value.
ADCMX2 and ADCMX1: These bits determine if internal or external temperature sense mode is selected. (See table below.)
ADCMX0: This bit puts the temperature sensor in auto zero state when it is set to logic 1. The autozeroing is used to cancel
internal offset effects.
Note: The above setup is not required if the temperature conversion ROM utility routine is used. All the required setup and tem-
perature measurement algorithm steps are handled in the utility routine and it returns the local or remote temperature result. The
temperature conversion utility ROM routine automatically adds the 12-bit signed offset stored in temperature offset register to
the final temperature result. See the utility ROM section (
Sections 15
and
16
) for details of the routine.
PIN NUMBER
SIGNAL
48-PIN 56-PIN
FUNCTION
AIN3 13 15
AIN2 14 16
AIN1 15 17
AIN0 16 18
ADC Analog Input/Remote Temperature Sensor. Analog input pins AIN2 and AIN0 are shared with the remote
temperature sensor drive line. If the remote temperature sensor drive circuit is not selected, the pin can be used
as a differential input to the multiplexer. In differential input configuration, AIN2 is referenced to AIN3 while AIN0
is referenced to AIN1. When selected, the remote temperature sensor drive circuit supplies suitable current levels
for biasing an external diode-connected transistor to monitor temperature away from the microcontroller. The
remote temperature measurement can be made either in single-ended or differential configuration (differential
measurements are likely to be more accurate). Note, in differential configuration, AIN3 is used as the return path
for AIN2, and AIN1 is used as the return path for AIN0.
ADCMX2 ADCMX1 FUNCTION
0 0 Internal diode-connected transistor based temperature measurement
0 1 Remote diode-connected transistor based temperature measurement on AIN0
1 0 Remote diode-connected transistor based temperature measurement on AIN2
1 1 Reserved
Maxim Integrated
- Functional Diagrams 1
- 1.1 Overview 7
- 1.1.2 Instruction Set 8
- 1.1.4 Register Space 8
- 1.2 Architecture 9
- 1.2.1 Instruction Decoding 10
- 1.2.2 Register Space 11
- 1.2.3 Memory Organization 13
- 1.2.3.2 Utility ROM 16
- 1.2.3.3 Data Memory 16
- 1.2.3.4 Stack Memory 17
- 1.2.3.7 Data Alignment 19
- CDA0 = 1 21
- 1.2.4 Interrupts 25
- 1.3 Programming 31
- 1.3.6.1 Sign Flag 37
- 1.3.6.2 Zero Flag 38
- 1.3.6.3 Equals Flag 38
- 1.3.6.4 Carry Flag 38
- 1.3.6.5 Overflow Flag 39
- 1.3.7.2 Unconditional Jumps 39
- 1.3.7.3 Conditional Jumps 40
- 1.3.7.4 Calling Subroutines 40
- 1.3.7.5 Looping Operations 40
- 1.3.8 Handling Interrupts 41
- 1.3.9 Accessing the Stack 42
- 1.3.10 Accessing Data Memory 43
- 1.4.19 General Register (GR) 59
- 2.1 Architecture 75
- 2.3 Supply Configuration 83
- 2.4 Linear Regulator 84
- 2.5 Power-On Reset 84
- 2.5.1 Power-Up Counter 85
- 2.5.3 Reset Output 87
- 2.7 Reset Mode 89
- 2.7.2 External Reset 90
- 2.7.3 Internal System Reset 90
- SECTION 3: ANALOG I/O MODULE 91
- 3.1.1 Analog I/O Pins 96
- Register Name: ACNT 98
- ADCMX2 ADCMX1 FUNCTION 99
- 1 1 Reserved 99
- Maxim Integrated 100
- Section 5 104
- Section 2 104
- Section 3.3.6 107
- Section 3.4 107
- Table 3-2. ADC Signals 108
- Section 3.3.10 110
- 3.3.4 Unipolar/Bipolar 111
- 3.3.5 Transfer Function 112
- Section 3.3.3 115
- Section 3.3.5 115
- 3.3.7 Analog Input Protection 116
- 3.3.8 ADC Clock 117
- 3.3.9 Auto Shutdown Mode 117
- 3.3.11 ADC Interrupts 122
- 3.3.12 Using the ADC 123
- 3.4 Temperature Sensor 124
- Sections 15 125
- TEMPERATURE (°C) 126
- Section 3.4.2 127
- Table 3-12. DAC Signals 128
- 3.5.4 DAC Power-Down 130
- 3.5.5 Using the DAC 130
- LIST OF FIGURES 133
- LIST OF TABLES 133
- 4.1 Architecture 134
- 4.2 CAN Controller Registers 136
- 4.3 CAN Operations 177
- 4.3.1.2 Remote Frame 180
- 4.3.1.3 Error Frame 181
- 4.3.1.4 Overload Frame 181
- 4.5 External Pins 182
- 4.7 CAN Interrupts 183
- 4.8.1 Message Center 15 185
- 4.9.2 Receiving Data Messages 186
- 4.15 Bit Timing 194
- 4.16 CAN Bus Activity 197
- 5.1 Architecture 200
- Section 3 204
- 76543210 205
- Reset 0 0 1 0 0 0 0 1 205
- Access rw r r rw rw rw rw rw 205
- 5.3 System Clock Generation 209
- 5.4 Watchdog Timer 215
- 5.5 Power Management Mode 217
- 5.5.2 Switchback Mode 218
- 5.5.3 Stop Mode 218
- SECTION 6: SERIAL I/O MODULE 219
- 6.1.1 UART Pins 223
- 6.2 UART Registers 223
- Serial Mode Definition 224
- — — — — — — — 226
- 6.3 Modes of Operation 227
- 6.3.3 UART Mode 2 230
- 6.3.4 UART Mode 3 230
- 6.4 Baud-Rate Generation 233
- 6.4.4 Baud-Clock Generator 234
- 6.5 Framing Error Detection 235
- 7.1 Architecture 238
- Compare Mode: 244
- Capture Mode: 244
- 7.2.3 Type 2 Reload Registers 248
- 7.3.3 16-Bit Counter 255
- 7.3.4 Dual 8-Bit Timers 256
- 7.4.3 Measure Period 259
- 8.1 Architecture 264
- 8.1.1 Port Pins 265
- 8.2 Port Registers 265
- 8.3 GPIO Operation 271
- 8.3.4 Port Pin Examples 273
- 9.1 Architecture 276
- 9.1.1 SPI Pins 277
- 9.2 SPI Peripheral Registers 277
- 9.3 SPI Operation 282
- 9.3.2 SPI Slave Operation 283
- 9.3.3 SPI Transfer Formats 284
- 9.4 SPI Transfer Baud Rates 285
- 9.5 SPI System Errors 285
- 9.6 SPI Interrupts 286
- 10.1 TAP Overview 289
- 10.2 Architecture 289
- 10.2.1 TAP Pins 290
- 10.3 TAP Interface Control 291
- 10.4 TAP Controller Operation 292
- 10.4.2 Run-Test-Idle 293
- 10.4.3 IR-Scan Sequence 293
- 10.4.5 Communication via TAP 294
- 11.1 Architecture 299
- Section 12 303
- Section 10 305
- Section 1 305
- 11.3 Debug Engine Operation 306
- 11.3.2 Breakpoint Registers 308
- 11.3.3 Using Breakpoints 310
- 11.3.4 Debug Mode 311
- 11.3.5 Debug Mode Commands 311
- 11.3.8 Return 313
- 12.1 Bootstrap-Loader Mode 317
- Section 11 318
- Section 12.5 320
- 12.5 JTAG Bootloader Protocol 321
- 13.6 Operand Count Selection 335
- 13.8 Accessing the Multiplier 336
- Acc.<b> 343
- 1000 1010 0001 1010 345
- 1101 1010 0010 1010 346
- 0011 1100 ssss ssss 349
- 0111 1100 ssss ssss 349
- 1111 1010 bbbb 1010 352
- 1101 1010 0000 1010 353
- 1110 1010 bbbb 1010 353
- 1101 1010 0001 1010 354
- 1ddd dddd 0bbb 0111 354
- 1ddd dddd 1bbb 0111 354
- 1000 1010 1001 1010 355
- .<b> 356
- 1110 1100 0000 1101 359
- 1001 1100 0000 1101 359
- 1101 1100 0000 1101 359
- 1100 1100 0000 1101 359
- 1000 1100 1000 1101 360
- 1010 1100 1000 1101 360
- 1110 1100 1000 1101 360
- 1001 1100 1000 1101 361
- 1101 1100 1000 1101 361
- 1100 1100 1000 1101 361
- 1000 1010 0100 1010 362
- 1000 1010 0101 1010 362
- 1000 1010 1100 1010 363
- 1000 1010 1101 1010 363
- 1000 1010 0010 1010 364
- 1000 1010 0011 1010 364
- 1000 1010 0110 1010 364
- 1000 1010 1010 1010 365
- 1000 1010 1111 1010 365
- 1000 1010 1110 1010 366
- 1000 1010 1011 1010 366
- 1000 1010 0111 1010 368
- 1000 1010 1000 1010 368
- 1011 1010 bbbb 1010 369
- WITH TYPE A FLASH) 371
- 15.2 Data Transfer Functions 372
- TYPE F FLASH) 378
- 16.2 Data Transfer Functions 383
- REVISION HISTORY 386
Manuais e produtos relacionados com Hardware Maxim-integrated MAXQ7666
Hardware Maxim-integrated MAXQ7667 Manual do Utilizador
(347 páginas)
(347 páginas)
Hardware Maxim-integrated MAXQ Family Users Guide: MAXQ8913 Supplement Manual do Utilizador
(114 páginas)
(114 páginas)
Hardware Maxim-integrated High-Speed Microcontroller Users Guide: DS80C390 S Manual do Utilizador
(158 páginas)
(158 páginas)
Hardware Maxim-integrated High-Speed Microcontroller Users Guide: Network Mi Manual do Utilizador
(221 páginas)
(221 páginas)
Hardware Maxim-integrated MAX31782 Manual do Utilizador
(223 páginas)
(223 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais